easy to use air driven liquid pump pneumatic types for machinery

Compressed Air Driven Liquid Booster Pump-DGGD Series

We offer the most complete range of Air driven liquid pump models in the industry measured for:

Capability of ultimate pressure, flow or output horsepower.

easy to use air driven liquid pump pneumatic types for machinery-1

Compatibility with a broad variety of liquids, such as oil, water and chemical applications.

SUNCENTER pumps are air driven at a drive air pressure of 1bar to 8bar (14.5 psi to116 psi) by the normal air compressor. Basically the principle of operation is similar to a reciprocating amplifier where control of the piston at the end position is regulated by a pilot operated 4/2 way valve.

Suncenter pumps feature a large air piston joint to a smaller diameter plunger. The pressure ratio is the difference of these two areas and is the method of determining maximum outlet pressure. Higher pressures obtained by using higher pressure ratios.Suncenter model numbers reflect the pumps nominal pressure ratios， while the technical data indicates exact ratios. The outlet pressure is easily to set through a simple air regulator. By multiplying the pressure ratio by the available shop air pressure, the nominal liquid pressure can be calculated.

SUNCENTER pumps are self priming. In general it is not necessary to use an air line lubricator. The liquid to be pumped flows into the suction chamber by the up-stroke of the drive piston. By this suction effect, the inlet check valve is opened and the outlet check valve is closed. The down-stroke generates the pressure at the liquid side. The inlet check valve is closed and the outlet check valve is opened by the generated pressure. SUNCENTER liquid pumps cycle automatically, where the pressure is built up the numbers of cycles slow down, the pump stops automatically when the output pressure forces are equal. The pump restarts with a slight drop in the outlet pressure or an increase in the air drive pressure. Pump performance can be affected by a number of conditions, such as freezing of muffler or pilot valves (which is caused by moisture in air lines), inadequate inlet air line sizes and dirty filers. Don’t reduce the indicated port sizes and consult SUNCENTER for exact flow conditions not shown in charts.

easy to use air driven liquid pump pneumatic types for machinery-2

DGGD Series Liquid Pumps(Double acting, single air drive head)

easy to use air driven liquid pump pneumatic types for machinery-3

◪ They are characterized by the same features as the DGG pumps single acting, single air drive head types, but they have less pulsations and deliver approx. 50 % more flow.

Model	Pressure Boost Ratio	Driven air pressure PL	Formula to calculate outlet pressure	MAX Outlet Pressure(bar)*	Liquid inlet Connection	Liquid outlet Connection	MAX Flow (L/min)**
DGGD4	4:1	2-8 bar	4XPL	32	NPT1/2	NPT1/2	70.00
DGGD6	6:1	2-8 bar	6XPL	48	NPT1/2	NPT1/2	48.60
DGGD10	10:1	2-8 bar	10XPL	80	NPT1/2	NPT1/2	30.61
DGGD16	16:1	2-8 bar	16XPL	128	NPT1/2	NPT1/2	19.73
DGGD28	28:1	2-8 bar	28XPL	224	NPT1/2	NPT1/2	11.30
DGGD40	40:1	2-8 bar	40XPL	320	NPT1/2	NPT3/8	7.69
DGGD64	64:1	2-8 bar	64XPL	512	NPT1/2	NPT3/8	4.94
DGGD80	80:1	2-8 bar	80XPL	640	NPT1/2	NPT3/8	3.96
DGGD100	100:1	2-8 bar	100XPL	800	NPT1/2	NPT3/8	3.13
DGGD130	130:1	2-8 bar	130XPL	1040	NPT1/2	M14*1.5	2.40
DGGD175	175:1	2-8 bar	175XPL	1400	NPT3/8	M14*1.5	1.81
DGGD255	255:1	2-8 bar	255XPL	2040	NPT1/4	M14*1.5	1.23
DGGD400	400:1	2-8 bar	400XPL	3200	NPT1/4	M14*1.5	0.79

features

※ Compressed Air driven - no electricity required (connect to normal air compressor)
※ In order to extend the lifetime of the pump, the driving air pressure should not be higher than 8 bar
※ No airline lubricator required
※ Pressures to 640Mpa (6400 bar)
※ Wide range of models with different ratios
※ Built-in-cooling on most models
※ Easy to install, operate and maintain
※ Best price / performance ratio
※ No heat, flame or spark risk and explosion proof
※ Automatic pressure holding, whatever the cause of the pressure drop, the Suncenter pump will automatically start, keep the loop pressure constant

video

y******m

The wood materials used in Suncenter air driven liquid pump have proven track record for performance and are sourced from established brands using reliable suppliers.

e******t

Suncenter pneumatic hydraulic pump high pressure has to be tested. It is carefully measured in terms of insole length, insole width, toe lift, heel height and back height for proper fitting, symmetry and sizing requirements. GJ Bush is top rubber bushing manufacturer since 1998, focusing on auto parts engine mounting and suspension bushings for more than 22 years

j******t

The production procedures of Suncenter pneumatic hydraulic pump high pressure include shaping, firing, glazing, and re-firing. All of these workmanships are done by skilfully technicians who have many years of experiences in porcelain. Our main products are rubber bushing, suspension bushings, engine mounting, strut mounting, etc

p******i

Suncenter air driven liquid pump has passed various kinds of tests according to international lighting standards. In some cases, some even tougher standards such as vibration test are adopted to make sure that it is going to last. Our main products are rubber bushing, suspension bushings, engine mounting, strut mounting, etc

b******l

Suncenter air driven liquid pump, containing sole, insole, outsole, midsole, heel, and upper, is manufactured by a variety of specialized CNC and laser machines. Nanchang Ganjiang Bush Factory is proud to provide premium quality OEM grade auto parts for over 20 years

z******j

air driven liquid pump uses a high-quality lens, which can enhance the contrast and clarity of the shooting picture, making the color of the picture more realistic and the quality of the picture more high-definition.

Mensaje del producto

*Nombre

Teléfono

*Correo electrónico

*Contenido